Building an internal USB hub for the X68000 expansion bay
The Sharp X68000 arrived before USB became a household interface, yet its expansion bay offers a tidy home for a genuinely useful modern accessory: an internal hub with accessible USB-A sockets. The computer will still need a working USB host adapter because a hub only manages downstream devices; it cannot create a USB host by itself. A successful build therefore combines an existing X68000 USB connection, a suitable hub controller and enough local power for the devices you intend to attach.
Treating the project as more than a plastic box with sockets helps. Measure the particular machine, document its bay connector and respect the limits of its host controller before ordering parts. The result can sit neatly inside the case while its sockets line up with the original panel, preserving the compact feel of the X68000 rather than turning it into a desk full of adaptors.
Choose a topology that matches the host
Start with the signal path. The X68000 host adapter should connect to the hub’s single upstream port; each keyboard, mouse, drive or adaptor then uses a downstream port. The bay itself may supply power, but it is not automatically a USB bus. Treat any data contacts on a drive connector as unknown unless the schematic or service documentation identifies them.
| Approach | Practical speed | Work required | Main advantage | Main limitation |
|---|---|---|---|---|
| Commercial USB 2.0 hub | Up to 480 Mbit/s | Mount an existing module and sockets | Fastest route to a working unit | The upstream adapter may limit the speed |
| Custom GL852G or FE2.1 board | Up to 480 Mbit/s | PCB layout and careful testing | Compact, controllable hardware | More design work |
| MAX3421E-based controller | Up to 12 Mbit/s | Firmware and device handling | Useful for keyboards and mice | No High Speed operation |
| Wired USB splitter | Unreliable | Wiring only | Almost no construction work | No proper hub negotiation or current protection |
Match the hub to the host before selecting components. If the X68000 adapter operates at Full Speed, every attached device is limited by that upstream connection even when the hub contains USB 2.0 silicon. For keyboards, mice and common card readers, that limitation is rarely troublesome. High-speed storage needs a host controller, driver and X68000 software that all support High Speed; a polished connector cannot provide those missing pieces.
Australian buyers have sensible sourcing options. Oztronics in Melbourne and Core Electronics in Queensland stock many common electronic parts, while element14 and RS Components operate Australian stores with GST-inclusive pricing. Compare that total with overseas listings after allowing for the Australian dollar exchange rate, international freight and possible import charges. For a first prototype, buying one known-good module locally can be cheaper than ordering several uncertain chips.
Fit the electronics into the expansion bay
X68000 variants do not present an identical expansion-bay envelope. Measure the opening, usable depth, mounting holes and clearance around any drive cage before making a bracket. The original machines, later Z-series cases and ACE arrangements can differ, so a drawing made for another model may leave the board unsupported or block a connector. A cardboard template is enough to reveal most of those problems.
Panel-mount USB-A sockets give the finished unit a professional appearance. Their pigtails should reach the controller board without creating long, exposed runs of sensitive differential wiring. The sockets also need rigid mechanical support; a small printed circuit board should not be expected to hold their weight. Keep the socket openings accessible, provide dust caps where possible and make sure the connector faces match the panel rather than forcing the user to look at the underside of the board.
Mount the board on nylon standoffs and leave space around regulators and the host controller. Airflow matters once several powered devices are attached, particularly in the tightly packed equipment found around Australian retro-computing collections. Local meetings in Melbourne, Brisbane and Sydney are good places to compare mounting ideas with people who own the same hardware. A compact, labelled design is much easier for another hobbyist to inspect, repair and reproduce.
Select a controller that suits the devices
A USB 2.0 hub controller such as the GL852G or FE2.1 offers four downstream ports and ample bandwidth for storage, scanners and other modern peripherals. These devices are usually accompanied by reference schematics and layout material, which saves considerable effort when the available documentation is incomplete. The MAX3421E is an alternative for a simpler Full Speed design, although it requires firmware and more work to implement hub and device-class behaviour.
High-speed capability on the hub does not remove the need to check the X68000 side. The upstream link must support the negotiated speed, and the computer’s software must enumerate the resulting topology. A Full Speed host can operate a compatible USB 2.0 hub at the lower rate, which is suitable for many low-bandwidth accessories but disappointing for large file transfers. Record the host adapter’s limitations alongside the schematic so the finished project does not promise performance the platform cannot deliver.
Pay close attention to the layout. USB data pairs benefit from a continuous ground plane, short connections, tightly controlled impedance and minimal branching. Follow the controller supplier’s guidance for series damping, pull-down resistors, crystal placement and decoupling. Place input protection close to each external connector, connect the ground reference properly and avoid routing data signals beside switching regulators. A compact layout is helpful only when it remains electrically sensible.
For the first working version, mounting a proven commercial module can be wiser than developing a controller board and hub firmware simultaneously. It establishes the mechanical arrangement, power budget and software compatibility before the PCB work begins. Once those constraints are known, the custom board can be designed around them instead of becoming a collection of optimistic assumptions.
Design a clean power path
Power budgeting is the part of an internal hub most likely to cause trouble. A USB 2.0 bus-powered device may request up to 100 mA, while a self-powered device can request as much as 500 mA. Those are limits rather than targets, and mechanical drives can draw additional current while spinning up. Give each output a sensible current limit and size the total supply for the devices that will actually be used.
Many X68000 expansion arrangements provide 5 V and sometimes 12 V, but the available current and the meaning of each pin must be confirmed for the particular model. If the 5 V rail is weak, 12 V can feed an efficient buck converter instead. A protected path should include input fusing, reverse-polarity protection, a load switch with current limiting and local bulk capacitors. Measuring the rails under load is more informative than relying on a label or an idle reading.
A self-powered hub must avoid back-feeding between the host’s upstream VBUS and the local downstream supply. Separate the paths, control their connection and test both states with the computer switched off. Indicator LEDs should use their own current limiting rather than loading a data or power pin. Keep heat-producing parts away from the socket area and provide enough copper or ventilation for sustained use.
Keep the hub electrically polite
USB requires a shared ground reference between the host and hub, so the project is not a galvanically isolated system. That does not justify connecting every bay pin together. Leave undocumented data contacts unused, insulate them where practical and keep the USB ground connection short and deliberate. The expansion connector should contribute power where it is rated to do so, not become an accidental network for signals the host was never designed to carry.
External sockets are the most likely entry point for electrostatic discharge. Fit low-capacitance ESD protection close to the connector and provide a chassis shield path that avoids passing discharge currents through sensitive logic. A common-mode choke can help where radiated or conducted interference becomes audible. If the board uses a metal bracket, decide deliberately how the shield and PCB ground meet; an accidental connection through a loose screw is neither repeatable nor serviceable.
The original X68000 power supply may already be old enough to sag under an additional load. Log the 5 V rail while the hub, a storage device and the computer are operating, then repeat the test with the original arrangement for comparison. A poor supply can imitate a faulty controller. Do not place a mains converter inside the computer; Australian mains is 230 V, and a low-cost external isolated supply with an RCD-protected outlet is the safer choice.
Bring the board up under controlled conditions
Before connecting anything to the X68000, inspect the PCB under magnification. Check for solder bridges, incomplete joints and reversed connectors. With power disconnected, confirm that each supply rail has the expected resistance to ground and that no data pair is shorted. A current-limited bench supply provides a controlled way to identify an excessive load before it reaches the computer’s original circuitry.
Connect the host and hub first with no downstream devices attached. Confirm that the hub appears in any available USB monitor and that its idle consumption is sensible. Add one device at a time, measuring the supply voltage and input current as each is introduced. Test enumeration, data transfer, hot-plug behaviour and any suspend or resume path used by the X68000. A hub that works with one keyboard can still fail when several devices request current simultaneously.
Electromagnetic interference deserves a separate check. A poorly terminated shield or an unfiltered power supply may disturb an AM radio, CB set or nearby computer equipment. Test the unit beside ordinary Australian broadcast receivers and watch for noise while moving USB cables. Secure the pigtails, inspect the shield termination and compare the result with the commercial module. This is also a sensible time to check connector temperature after a sustained transfer.
Photograph the finished assembly from both sides and keep those images with the schematic and bill of materials. For older X68000 documentation preserved as slides or negatives, Nikon Coolscan resources provide useful film-scanning guidance; a camera or flatbed scanner remains more practical for recording solder-mask details and board revisions.
Put the finished hub into daily use
The completed hub can serve modern keyboards, mice, card readers, serial adaptors and suitably supported storage devices. Its main advantage is physical tidiness: the cables remain inside the case and only the required connectors appear at the rear or side panel. Fit the unit with the original X68000 nearby, because host-adapter placement and cable length can affect reliability when several devices are connected.
Software support remains as important as hardware. The X68000 must have a USB host stack, suitable device drivers and applications capable of using the resulting device. A mass-storage device needs a compatible driver, while a serial adaptor depends on its own emulation and port support. The hub makes the physical connection possible; it does not remove those operating-system requirements.
The X68000 build diary provides a practical home for a dated schematic, board photographs, test notes and compatibility findings. Build one documented and reproducible unit, then post it up through the X68000 hobbyist community with the bill of materials and measured power figures so the next maker can construct, test and improve the internal USB hub without repeating the same dead ends.
Nereid-X Expansion Board
A personally-produced LAN+USB+Memory expansion board for Sharp X68000 series computers. Multiple production runs were offered, including a final batch and a later revival reproduction run.
Power Supply Repair
X68 power supply repair and modification services were offered by the site owner, with documentation shared through diary entries spanning 2001–2006.
Server & Networking
Notes on FreeBSD administration, ISP changes, server migration, and networking topics. The site itself ran on FreeBSD with the hns diary system and Namazu search integration.
Get in touch
X68K.NET connects Sharp X68000 enthusiasts through community links and shared projects. Reach out with questions about the Nereid project or X68 resources.