Modding the X68000 PSU with a soft-start circuit

An original Sharp X68000 often needs more than a new fuse before it can be used reliably. Switch-on current can stress aged components inside the power supply. A soft-start circuit limits that initial surge while the reservoir capacitor charges, then removes the restriction once the output is stable.

This should be a preservation exercise, not a way to ignore electrical faults. Leakage, overheated regulators, cracked solder joints and poor rectifier connections still need attention. The modification should protect an otherwise sound supply while keeping the machine recognisable, repairable and safe for the next owner.

The approach here suits an original-style linear supply using a transformer, bridge rectifier, bulk capacitor and series regulators. Exact rails and component values must come from the schematic and board markings for that revision. Japanese-market machines and later replacement supplies differ, so a circuit should never be copied from a photograph alone.

Good records include the original wiring, component part numbers, measured voltages and the reason for each change. Reversible work is easier to service. Australian owners also need to account for 230-volt mains, state electrical rules and the parts actually available locally.

Choosing the right modification

Approach Initial behaviour Typical additions Main trade-off
Unmodified supply Unrestricted surge None Simple, but ageing parts receive the full startup stress
Fixed pre-charge resistor Limited while charging Resistor and bypass relay Significant heat if the bypass fails
Thermistor with relay bypass Self-limiting while charging NTC thermistor, relay and driver Requires correct sizing and timing
Active current limiter Controlled by the driver Control circuit and switching stage More complex and less reversible

For a first project, favour a circuit that fits on a small board and can be removed without destroying original tracks. The options below suit different levels of complexity. Replacing the supply with a modern switching unit may be simpler, but it requires a different wiring, grounding and protection strategy rather than a drop-in circuit.

Measure before choosing. Establish the unloaded output voltages, the load current expected from the X68000 and the charging behaviour of the reservoir capacitor. Replace obviously damaged parts first. A soft-start network cannot cure excessive ripple or a regulator that fails once warm, and compensating for either fault may conceal the real problem.

Why the supply struggles at switch-on

The surge has two sources. The transformer draws magnetising current as its flux builds, while the rectifier charges the reservoir capacitor. A series element in the rectifier return helps against the capacitor surge. It does little for transformer inrush, so the finished result should not be described as eliminating every transient.

Load dump is related but different. As the input falls, stored charge can be returned through rectifier junctions, adding stress to diodes and nearby components. Slowing the initial charge reduces the worst case without making the supply immune to an abrupt disconnection. Correct fusing, adequate ratings and sound construction remain the primary protection.

The habit of recording materials, construction and repair is not confined to computing, which is why independent fashion publishing offers a useful parallel for a preservation-minded hobbyist. Photographs of the original board and a clear record of each alteration give an X68000 supply that same long-term care. They also help another hobbyist distinguish an intentional change from an ageing component that has failed.

Designing the pre-charge path

Identify the bridge rectifier, reservoir capacitor and their connections before drawing anything. In a negative-return arrangement, a power NTC thermistor or suitable resistor can sit between the bridge's negative terminal and the capacitor's negative terminal. A relay shorts that element after startup. Check the board, since some designs route the return differently and some power supplies already include an active soft-start stage.

Size the component for the actual capacitor, not a generic example. A power NTC thermistor must tolerate the peak charging current and stored-energy pulse. For a fixed resistor, calculate pulse energy and the heat produced if the bypass relay fails. An automotive relay may handle the contact duty better than a small signal relay, but its coil voltage, contact ratings and isolation still need checking.

Keep mains-current paths separate from the timing electronics. The high-current path needs short wiring, adequate copper area and secure joints; the control circuit needs a safe low-voltage supply, not an improvised mains-powered breadboard. If an existing controller already manages startup, a second delay mechanism may open the relay during running or prevent the supply from starting correctly.

Timing the bypass relay

An RC delay can operate a transistor driver that energises the bypass relay, but the delay must be measured rather than guessed. It should allow the reservoir voltage to settle while still supporting the load after closure. Fractions of a second to a few seconds are common starting ranges, but capacitance, load and the supply's undervoltage threshold determine the useful value.

Use an undervoltage or brownout detector where possible, so the relay releases if the input collapses and re-arms after a clean restart. A normally open contact across the limiting element gives a useful failure mode: loss of the control supply leaves the element in the charging path. Fit the manufacturer's recommended flyback suppression across the relay coil, and test the driver separately at low voltage.

A relay click does not prove that the sequence was safe. Measure the capacitor voltage before and after closure, check the thermistor's temperature and confirm that the output does not dip below the X68000's requirement. Too short a delay can cause a second surge; too long a delay can prevent regulation. Both need a revised circuit, not a larger capacitor or a stronger relay.

Working safely with Australian mains

Mains electricity and the charged reservoir capacitor deserve the same respect in Sydney as anywhere else in Australia. A low-voltage isolation transformer does not make a defective board safe, and a residual-current device is not a substitute for isolation. Switch off, unplug and verify the supply is dead before touching it. Discharge the reservoir capacitor with an appropriately rated resistor and insulated probe.

Australian mains is nominally 230 volts at 50 hertz, while Japanese domestic equipment commonly used 100 volts at either 50 or 60 hertz. Check the label and service information before applying power. A 100-volt-only unit needs a suitable step-down arrangement and the correct fuse; do not assume an imported machine can receive 230 volts. Preserve the original protective-earth wiring rather than using an adapter to sidestep the question.

Electrical work is regulated by state and territory rules. In New South Wales and Victoria, household electrical work is generally restricted to licensed or authorised people; other jurisdictions have their own requirements and exemptions. Check the rules before altering the mains wiring, because private ownership does not remove the duty of care. Selling a finished unit can also bring RCM registration, testing and supplier obligations into play, with exemptions that must be considered separately from private hobby use.

The local parts market is practical. Australian distributors such as element14 and RS stock relays, transistors and passives, while component shops in Melbourne, Sydney and Brisbane can help with unusual capacitors. Specify voltage, current, tolerance and temperature rating rather than buying by appearance. Use a properly made AS/NZS 3112 mains lead and appropriate insulation; a travel adaptor is not a substitute for correct wiring.

Testing before connecting the X68000

Test the modified supply without the computer attached. Use a suitably rated dummy load and verify every output against the service information; do not assume that a 5-volt rail is the only load. A current-limited isolation transformer provides a useful test environment when installed by a competent person, but it does not remove the need to inspect wiring, insulation and polarity.

Record the startup current, capacitor voltage, relay timing and output voltages at several points during warm-up. Repeat the test from cold, then after the unit has run for an hour. Watch the thermistor and relay for excessive heat, and confirm that output stays within the X68000's requirements under representative load. A driver board can be tested using a laboratory supply before it is connected to the power-supply control rail.

The same careful documentation applies to the machine's controls. The USB keyboard adapter is a useful companion reference for recording connector details, enclosure fit and wiring changes before committing to a design. It is not part of this power supply circuit, but it demonstrates why clear notes are more valuable than a photograph of a completed board.

Share the modification and keep it running

Write a dated schematic, a component list, board-layout notes and photographs of the original and modified supply. Label the added board with the revision and date, and keep the original parts. A reversible harness and a sensible layout make a future fault easier to diagnose than a bundle of undocumented wires.

Include the measured values that matter: output voltages, startup current, bypass timing and the thermistor temperature under load. Add a fault indicator for a failed bypass relay if it can be done safely, and keep the fuse, capacitor and relay accessible for future service. Leave ventilation around the supply, since an original-style linear unit can remain warm even after its inrush has been tamed.

If you are building this circuit, post your schematic, photographs and test results on X68K.NET so another owner can check the work rather than repeat the same mistakes. Keep the safety warnings with the technical notes, and treat the finished modification as a documented part of the X68000's preservation, ready for the next person who needs to switch it on.

Nereid-X Expansion Board

A personally-produced LAN+USB+Memory expansion board for Sharp X68000 series computers. Multiple production runs were offered, including a final batch and a later revival reproduction run.

Power Supply Repair

X68 power supply repair and modification services were offered by the site owner, with documentation shared through diary entries spanning 2001–2006.

Server & Networking

Notes on FreeBSD administration, ISP changes, server migration, and networking topics. The site itself ran on FreeBSD with the hns diary system and Namazu search integration.

A two-ink risograph print in muted slate-blue and charcoal on off-white paper, showing a stylized desktop computer monitor beside a circuit board with soft geometric trace lines, conveying a calm retro-computing workshop atmosphere. A two-ink risograph print in deep purple and dark grey on cream stock, depicting a compact expansion card with connector ports and subtle Japanese technical annotations, evoking a hobbyist electronics bench. A two-ink risograph print in teal and charcoal on warm white paper, showing a server rack silhouette with soft network-line motifs and a small weather icon, suggesting a personal server room corner.

Get in touch

X68K.NET connects Sharp X68000 enthusiasts through community links and shared projects. Reach out with questions about the Nereid project or X68 resources.